Bidford-on-Avon, Warwickshire. Mon to Fri.01789 224228

Illustrative example · Domestic appliances · LSR

Worked Example: Appliance Silicone Valve

A small silicone valve inside a domestic appliance. Never seen by the user, but it has to work every cycle for the life of the appliance. This is how we would typically approach long-run supply into a mature programme.

Domestic applianceSector
LSRTypical route
Long lifeMulti-year supply
2019Established

The brief

A valve component with a long product life and no room for supply drift.

Illustrative example: Repeated silicone valve parts in tray beside worn production tool
Stable valve production with matched repeat parts

Picture a small silicone valve that regulates fluid flow inside a family of kitchen appliances. It isn't visible and it isn't marketed. It just has to work every cycle for the life of the appliance.

A brief like this usually comes from a mature programme, often one where the existing supply has become less consistent. What the OEM typically needs is a supplier who will hold the valve stable for the rest of the product life, with proper material and process discipline.

The problem

A mature part that needs steady attention.

Valves like this are rarely complex. Typically it's LSR-moulded on a single-cavity tool with straightforward geometry. What matters is a specific hardness, a specific identifying colour and a specific tolerance on the sealing face, all held stable.

On a mature programme, small changes in grade or colour can slip through and turn into field returns that the OEM's quality team then has to investigate. The design rarely changes, so the risk sits in the material and the process.

We would typically propose a formal material and process specification, a retained golden sample, and regular contact that surfaces any change before it reaches a batch.

Illustrative example: Tray of moulded O-rings, gaskets and profile seals on a stainless inspection bench.

What we would change

How we would take over the programme and hold it stable.

Nothing exotic. Just steady discipline applied to a mature part.

  1. Tool transfer and inspection

    Where an existing LSR tool is transferred, we would inspect the cavity and measure first parts against the drawing. Tool ownership is agreed on your quotation.

  2. Material grade documented

    The LSR grade is documented and locked, with the supplier's documentation on file. Any change would need the OEM's sign-off first.

  3. Colour matched against a retained sample

    The identifying colour would be matched against a retained sample from approved batches, and the pigment recipe recorded.

  4. Sealing face checks

    The critical sealing face dimension would typically be checked on first-off parts, so drift is caught early.

  5. Batch traceability on request

    Batch traceability is available on request, in the format the OEM's quality system expects.

  6. Named engineer on the account

    One engineer owns the programme, and the OEM's engineering team has their direct line.

Illustrative example: Inspection bench with valve parts, open tool and colour references
Inspection and control for a transferred valve programme

Commercial trade-offs

What a programme like this would typically involve commercially.

Where the tooling already exists, the commercial conversation is usually less about unit price and more about reliability and communication.

For a mature programme, those are often the bigger levers. We'll confirm pricing and lead times on your quotation.

Services used

How we'd deliver a programme like this.

LSR injection moulding

Two-part liquid silicone metered, mixed, injected cold and cured hot. The cleanest route we have for medical, wearable and electronics parts at…

See the service

Tooling and part continuity

For parts that will be in production for years — components inside a device family, sealing parts on long-lived equipment, consumer parts on a…

See the service

Gasket and seal manufacture

Silicone and rubber gaskets moulded to your drawing, in the grade and hardness your sealing job actually needs. Enclosure gaskets, static fluid…

See the service

More worked examples

Other programmes worth reading.

Illustrative example: Sealed cable connector overmould with a cut sample on a bench

Worked Example: Marine Connector Overmould

A connector on a sensor cable that sits in salt water. This is how we would typically approach replacing a potted joint and heat-shrink with a single…

Read the example
Illustrative example: Fabric-reinforced rubber diaphragms beside an open compression mould tool

Worked Example: Industrial Pump Diaphragm

A fabric-reinforced pump diaphragm where replacement parts fail early. This is how we would typically re-tool it in compression with the fabric layer…

Read the example
A TCI multi-cavity sheet mould on the production line

Worked Example: Wearable Overmoulded Button

Three separate parts bonded together by hand, failing at the bond line in drop testing. This is how we would typically approach moving the assembly to…

Read the example

Next step

If your project rhymes with this one, get in touch.

The commercial shapes described in our worked examples are illustrative, not prices we're quoting today. Every programme sizes differently based on part geometry, annual volume, material family and paperwork requirements.

For a first conversation about whether we'd be the right supplier for your part, send a drawing or a sample with your rough annual volume. That's enough to know if the fit is real.

Designed and developed in the UK. Compression moulding and LSR on our own presses, with other work through our partner network. We'll confirm where your parts are made on your quotation.

At a glance

The idea in a picture.

How overmoulding works

Silicone moulded overPlastic, metal or electronicsBonded interface

Swipe to see the whole diagram

The rigid part goes into the tool and silicone is moulded around it, so you get one finished part.

Get in touch

Tell us the part, the volume, and the timeline.

Rough annual volume, target unit price, and any deadlines. That's enough to work out whether compression, LSR injection or something else is the right tool.

Real people, a real workshop

You deal with the people who make it.

No call centre and no middlemen. When you contact TCI Products, you speak to the team who design, build and check your mould.

  • A real Warwickshire workshopUnit 15, Waterloo Park, Bidford-on-Avon, Alcester B50 4JG.
  • Real people on the phoneCall the team on 01789 224228, Monday to Friday.
  • The same team on every jobDesign, production and aftercare come from the people you see here.
  • Part of TCI GroupFour specialist divisions under TCI Group, one engineering team. Visit TCI Group.
Representative image: a design and project office.
Representative image: a design and project office.
Representative image: moulds on the bench mid-build.
Representative image: moulds on the bench mid-build.
Representative image: a stack of silicone moulds.
Representative image: a stack of silicone moulds.
  • Thomas LaneManaging Director
  • George PrestonDesign & Project Manager
  • Kelly BallingerHead of Partnerships
  • Jim AndertonProduction Manager
  • TheodoreEmployee Welfare
Meet the team