Bidford-on-Avon, Warwickshire. Mon to Fri.01789 224228

Illustrative example · Medical device · LSR

Worked Example: Medical Device LSR Gasket

A sealing gasket for a hand-held device housing. When a compression-moulded part needs hand-trimming on the sealing face, it stops scaling with volume. This is how we would typically approach the move to LSR.

Medical deviceSector
LSRTypical route
Cold runnerTool type
2019Established

The brief

A seal that has to be right on the sealing face, batch after batch.

Illustrative example: Silicone gaskets showing sealing lip edge quality on inspection bench
Sealing lip quality on silicone gaskets

A typical brief: a hand-held diagnostic device has a sealed enclosure with a silicone gasket around the perimeter, keeping dust and moisture out during use and cleaning.

Where the gasket runs on compression tooling with the parting line at the edge of the sealing face, every part can need hand-trimming. As volumes grow, hand-trim becomes the bottleneck, and cosmetic expectations often tighten as well.

The problem

When the parting line is in the wrong place, hand-trim becomes the constraint.

Compression tools are often designed with the parting line at the widest point of the cross-section, because it's the easiest place to machine. If that's also the sealing face, every part comes off the tool with a fine witness line on the seal.

As volume rises, adding trim operators is slow and expensive. The better answer is usually a tool that doesn't need trimming.

We would typically propose moving to LSR with a cold-runner tool, relocating the parting line onto the hidden underside of the gasket and specifying the cavity finish to leave the sealing face untouched.

Illustrative example: Opened LSR tool holding pale silicone gaskets with clean hidden parting line

What we would change

How we would move the parting line, go to LSR and remove the hand-trim.

One geometry decision, plus a change of manufacturing route.

  1. Relocate the parting line

    The parting line moved to the underside of the gasket, where it seats into the housing and any witness is hidden.

  2. Move the material to LSR

    The same silicone family in an LSR grade documented for medical device applications, with the supplier's documentation for the grade. Batch traceability is available on request.

  3. Cut a cold-runner tool

    A cold-runner design that keeps sprue marks off the finished part.

  4. Specify the sealing-face finish

    The cavity polished on the sealing face to leave a defined finish, with first parts measured against the drawing.

  5. Run validation batches

    Validation batches agreed with you before production release.

  6. Plan the transition

    Existing supply can continue while the new tool proves itself, so the switch-over is planned rather than rushed.

Illustrative example: Cold runner LSR tool and finished pale gaskets with underside parting line
LSR gasket moulding with hidden parting line

Commercial trade-offs

How the trade-off would typically look.

LSR tooling usually costs more than a compression tool. In exchange, removing the trim operation typically lowers per-part cost and frees up the capacity the trim was using.

Whether LSR is right depends on volume. At lower volumes compression can be the right answer.

Services used

How we'd deliver a programme like this.

LSR injection moulding

Two-part liquid silicone metered, mixed, injected cold and cured hot. The cleanest route we have for medical, wearable and electronics parts at…

See the service

Medical-grade manufacturing

Silicone moulding for medical device makers using medical-grade materials to a documented specification, with batch traceability from drum to…

See the service

Gasket and seal manufacture

Silicone and rubber gaskets moulded to your drawing, in the grade and hardness your sealing job actually needs. Enclosure gaskets, static fluid…

See the service

More worked examples

Other programmes worth reading.

A black TCI shaped-cavity silicone mould

Worked Example: Silicone Ear Tips

Small, soft, colour-critical parts that people wear for hours. This is how we would typically take a hand-cast pilot design into production tooling…

Read the example
Illustrative example: Silicone keypad mats and inspection tools on a workshop bench

Worked Example: Electronics Keypad Batch

A silicone keypad mat for a hand-held industrial device. Buttons that feel decisive without being noisy, conductive contacts that close reliably, and…

Read the example
Illustrative example: Black rubber seals in trays beside a compression mould tool

Worked Example: Automotive Moulded Seal

A rubber sealing component supplied into a tier-1 that fits it into a vehicle. Not exotic and not complex, but it has to arrive when the build schedule…

Read the example

Next step

If your project rhymes with this one, get in touch.

The commercial shapes described in our worked examples are illustrative, not prices we're quoting today. Every programme sizes differently based on part geometry, annual volume, material family and paperwork requirements.

For a first conversation about whether we'd be the right supplier for your part, send a drawing or a sample with your rough annual volume. That's enough to know if the fit is real.

Designed and developed in the UK. Compression moulding and LSR on our own presses, with other work through our partner network. We'll confirm where your parts are made on your quotation.

At a glance

The idea in a picture.

Which route suits your quantity

PrototypesHundredsThousandsTens of thousandsPrototype toolingCompression mouldingTransfer mouldingSolid silicone injectionLSR injection

Swipe to see the whole diagram

A general picture. Shape, material and detail also decide the route, and we talk it through with you.

Get in touch

Tell us the part, the volume, and the timeline.

Rough annual volume, target unit price, and any deadlines. That's enough to work out whether compression, LSR injection or something else is the right tool.

Real people, a real workshop

You deal with the people who make it.

No call centre and no middlemen. When you contact TCI Products, you speak to the team who design, build and check your mould.

  • A real Warwickshire workshopUnit 15, Waterloo Park, Bidford-on-Avon, Alcester B50 4JG.
  • Real people on the phoneCall the team on 01789 224228, Monday to Friday.
  • The same team on every jobDesign, production and aftercare come from the people you see here.
  • Part of TCI GroupFour specialist divisions under TCI Group, one engineering team. Visit TCI Group.
Representative image: a stack of silicone moulds.
Representative image: a stack of silicone moulds.
Representative image: a design and project office.
Representative image: a design and project office.
Representative image: moulds on the bench mid-build.
Representative image: moulds on the bench mid-build.
  • Thomas LaneManaging Director
  • George PrestonDesign & Project Manager
  • Kelly BallingerHead of Partnerships
  • Jim AndertonProduction Manager
  • TheodoreEmployee Welfare
Meet the team