Bidford-on-Avon, Warwickshire. Mon to Fri.01789 224228

Illustrative example · Wellness · Compression

Worked Example: Silicone Applicator Tip

A soft silicone tip for a personal care device. Skin contact, cleanable and colour-matched to the brand. This is how we would typically approach batch supply against a fluctuating retail programme.

WellnessSector
CompressionTypical route
Skin contactGrade
2019Established

The brief

A tip that goes onto skin and has to be right on colour, feel and durability.

Illustrative example: Warm rose silicone applicator tips showing softness and surface finish
Applicator tips matched for feel and colour

A typical brief: a personal care device with a replaceable silicone applicator tip, sold as a consumable.

The tip is skin contact. It has to be soft enough to be comfortable but firm enough to work, match a specific brand shade and stand up to daily cleaning. Demand usually follows retail seasons, so supply runs in batches with the tooling held between runs.

The problem

The challenge is a batch model with consistent colour and feel.

For a consumable, unit cost matters, so tooling has to fit the retail price point.

Compression tooling is usually the natural route for moderate volumes. The harder part is colour discipline and batch continuity over the product's life.

Colour would be matched against a physical chip signed off by your product team, with the pigment recipe recorded, so later batches can be checked against the same chip under standard lighting.

Surgical team in an operating theatre

What we would change

How we would tool in compression, lock colour and feel, and run to forecast.

Standard moulding; the programme discipline is what makes it repeatable.

  1. Compression tool for the tip

    A multi-cavity compression tool sized to the forecast.

  2. Skin-contact grade specified

    A platinum-cure silicone grade with the supplier's skin-contact documentation. Batch traceability is available on request.

  3. Colour matched against your chip

    Colour matched against a physical chip from your brand team, with the pigment recipe recorded.

  4. Feel signed off on moulded samples

    Samples pressed in a few durometers so your team can choose the right feel, then the grade is locked.

  5. Batches against your forecast

    Larger batches ahead of peak seasons and smaller ones in between. Tool storage and stock holding can be arranged; we'll agree terms on your quotation.

  6. First-off against the reference

    First-off parts compared to the golden sample and the colour chip.

Illustrative example: Open multi-cavity compression tool with coloured silicone charges
Compression tool set for applicator tip production

Commercial trade-offs

What would typically matter commercially.

On a consumable, the tooling has to sit comfortably within the retail price, so tool size and cavity count are matched to the forecast.

Batch flexibility matters as much as unit cost. Tooling and unit cost are quoted as separate lines on your quotation.

Services used

How we'd deliver a programme like this.

Compression moulding

Solid silicone or rubber pre-formed, loaded into a heated steel tool, and pressed under cure. Sensible tooling cost, built for repeat batches, and…

See the service

Wearable and consumer silicone

Silicone parts for products people wear, hold, or wipe every day — ear tips, straps, grips, sleeves, applicators. Made to a colour and feel you sign…

See the service

Batch manufacturing

For volumes measured in the hundreds or low thousands per batch, released on your schedule rather than ours. Bridge tooling, dedicated compression,…

See the service

More worked examples

Other programmes worth reading.

Illustrative example: Overmoulded whistle parts with soft silicone mouthpieces on a bench

Worked Example: Overmoulded Whistle

A referee whistle with a soft silicone mouthpiece bonded to a rigid plastic body, used in all weathers. This is how we would typically approach a…

Read the example
Illustrative example: Compression press and trays of textured rubber grips in a workshop

Worked Example: Outdoor Rubber Grip

A textured rubber grip fitted to outdoor equipment. It needs to be UV-stable, weather-resistant and comfortable in cold and wet conditions. This is how…

Read the example
Illustrative example: Small silicone valves in a tray beside a multi-cavity tool.

Worked Example: Appliance Silicone Valve

A small silicone valve inside a domestic appliance. Never seen by the user, but it has to work every cycle for the life of the appliance. This is how…

Read the example

Next step

If your project rhymes with this one, get in touch.

The commercial shapes described in our worked examples are illustrative, not prices we're quoting today. Every programme sizes differently based on part geometry, annual volume, material family and paperwork requirements.

For a first conversation about whether we'd be the right supplier for your part, send a drawing or a sample with your rough annual volume. That's enough to know if the fit is real.

Designed and developed in the UK. Compression moulding and LSR on our own presses, with other work through our partner network. We'll confirm where your parts are made on your quotation.

Get in touch

Tell us the part, the volume, and the timeline.

Rough annual volume, target unit price, and any deadlines. That's enough to work out whether compression, LSR injection or something else is the right tool.

Real people, a real workshop

You deal with the people who make it.

No call centre and no middlemen. When you contact TCI Products, you speak to the team who design, build and check your mould.

  • A real Warwickshire workshopUnit 15, Waterloo Park, Bidford-on-Avon, Alcester B50 4JG.
  • Real people on the phoneCall the team on 01789 224228, Monday to Friday.
  • The same team on every jobDesign, production and aftercare come from the people you see here.
  • Part of TCI GroupFour specialist divisions under TCI Group, one engineering team. Visit TCI Group.
Representative image: a stack of silicone moulds.
Representative image: a stack of silicone moulds.
Representative image: a design and project office.
Representative image: a design and project office.
Representative image: moulds on the bench mid-build.
Representative image: moulds on the bench mid-build.
  • Thomas LaneManaging Director
  • George PrestonDesign & Project Manager
  • Kelly BallingerHead of Partnerships
  • Jim AndertonProduction Manager
  • TheodoreEmployee Welfare
Meet the team