Bidford-on-Avon, Warwickshire. Mon to Fri.01789 224228

Illustrative example · Precision electronics · Compression

Worked Example: Electronics Keypad Batch

A silicone keypad mat for a hand-held industrial device. Buttons that feel decisive without being noisy, conductive contacts that close reliably, and consistency from batch to batch. This is how we would typically approach it.

Precision electronicsSector
CompressionTypical route
FeelSigned off on parts
2019Established

The brief

A keypad for a hand-held industrial instrument.

Illustrative example: Silicone keypad mats beside test jig and carbon pills
Keypad batches compared against a fixed reference

A typical brief: a hand-held instrument for field engineers uses a silicone rubber keypad over a PCB, and the feel of the buttons matters to its users.

Where batch drift has crept in, successive batches can feel slightly different, and users notice. What the maker usually needs isn't a redesign but the discipline to hold the feel consistent.

The problem

Drift usually sits in the material and process, not the drawing.

Feel drift typically comes from small changes that add up: a silicone grade swapped upstream without being flagged, or a cure cycle adjusted for cycle time. Together they change the actuation force and the click.

The fix isn't to redesign the keypad. It's to lock the grade and cure conditions, and to set a golden sample so any future drift can be caught at first-off.

We would also typically press sample mats in the current durometer and one either side, so your product team can confirm that the current spec is the right one.

Remote control with silicone keypad

What we would change

How we would lock the grade, set a golden sample and confirm the feel.

The hard part isn't the moulding. It's documenting the moulding so it can't drift.

  1. Grade specification locked

    Silicone grade documented and signed off. Any change would need your approval.

  2. Durometer comparison

    Sample mats in the current grade and one either side, for your team to compare in use.

  3. Golden sample set

    A golden sample from the first batch after the grade lock, retained and referenced for later batches.

  4. Cure cycle documented

    Cure temperature, time and pressure documented, with any deviation needing quality sign-off.

  5. Contact placement checked

    Conductive contact placement checked on first-off parts, because the electrical function matters as much as the feel.

  6. Batch supply against the reference

    Batches produced against your schedule, with first-off parts compared to the golden sample.

Illustrative example: Test keypad mats and golden sample on inspection bench
Test mats used to lock keypad feel

Commercial trade-offs

What a transition like this would typically involve commercially.

Where you already own the tool, a transition like this usually builds on the existing tooling, with material and process discipline added. Tool ownership is agreed on your quotation.

For a mature product with a stable drawing, this kind of move is often more about consistency than cost. We'll confirm pricing on your quotation.

Services used

How we'd deliver a programme like this.

Keypad and button manufacture

Silicone keypad mats and moulded buttons with a defined tactile feel, integrated conductive contacts, and graphics either printed on top or moulded…

See the service

Compression moulding

Solid silicone or rubber pre-formed, loaded into a heated steel tool, and pressed under cure. Sensible tooling cost, built for repeat batches, and…

See the service

Electronics-grade manufacturing

Silicone moulding for electronics OEMs — insulating gaskets, sealing membranes, keypad mats, connector boots, enclosure seals. Electronics-grade…

See the service

More worked examples

Other programmes worth reading.

Illustrative example: Black rubber seals in trays beside a compression mould tool

Worked Example: Automotive Moulded Seal

A rubber sealing component supplied into a tier-1 that fits it into a vehicle. Not exotic and not complex, but it has to arrive when the build schedule…

Read the example
Illustrative example: Small silicone diaphragm held in gloved fingers above a parts tray

Worked Example: Haptics Silicone Diaphragm

A precision-shaped silicone diaphragm that generates haptic feedback in a small consumer device. This is how we would typically move a cast prototype…

Read the example
Illustrative example: Soft silicone applicator tips in a tray with one held up

Worked Example: Silicone Applicator Tip

A soft silicone tip for a personal care device. Skin contact, cleanable and colour-matched to the brand. This is how we would typically approach batch…

Read the example

Next step

If your project rhymes with this one, get in touch.

The commercial shapes described in our worked examples are illustrative, not prices we're quoting today. Every programme sizes differently based on part geometry, annual volume, material family and paperwork requirements.

For a first conversation about whether we'd be the right supplier for your part, send a drawing or a sample with your rough annual volume. That's enough to know if the fit is real.

Designed and developed in the UK. Compression moulding and LSR on our own presses, with other work through our partner network. We'll confirm where your parts are made on your quotation.

Get in touch

Tell us the part, the volume, and the timeline.

Rough annual volume, target unit price, and any deadlines. That's enough to work out whether compression, LSR injection or something else is the right tool.

Real people, a real workshop

You deal with the people who make it.

No call centre and no middlemen. When you contact TCI Products, you speak to the team who design, build and check your mould.

  • A real Warwickshire workshopUnit 15, Waterloo Park, Bidford-on-Avon, Alcester B50 4JG.
  • Real people on the phoneCall the team on 01789 224228, Monday to Friday.
  • The same team on every jobDesign, production and aftercare come from the people you see here.
  • Part of TCI GroupFour specialist divisions under TCI Group, one engineering team. Visit TCI Group.
Representative image: moulds on the bench mid-build.
Representative image: moulds on the bench mid-build.
Representative image: a stack of silicone moulds.
Representative image: a stack of silicone moulds.
Representative image: a design and project office.
Representative image: a design and project office.
  • Thomas LaneManaging Director
  • George PrestonDesign & Project Manager
  • Kelly BallingerHead of Partnerships
  • Jim AndertonProduction Manager
  • TheodoreEmployee Welfare
Meet the team