Bidford-on-Avon, Warwickshire. Mon to Fri.01789 224228

Illustrative example · Marine equipment · Cable overmould

Worked Example: Marine Connector Overmould

A connector on a sensor cable that sits in salt water. This is how we would typically approach replacing a potted joint and heat-shrink with a single silicone overmould that grips the jacket.

MarineSector
OvermouldTypical route
SealedCable entry

The brief

A connector that lives in salt water.

Illustrative example: Prepared cable connector joint before silicone overmould sealing
Connector joint prepared for sealed overmoulding

A typical brief: marine monitoring equipment uses a connector on a sensor cable that sits permanently in seawater, and corrosion is appearing inside the connector body.

A common cause is a potted joint covered with hand-applied heat-shrink, where water wicks along the cable jacket under the heat-shrink and reaches the pins. The question is usually whether an overmould could seal the joint more reliably and reduce the hand work.

The problem

The seal needs to be on the jacket, not the heat-shrink.

Heat-shrink seals well to itself but not always reliably to the cable jacket, especially after temperature cycling. Potting seals the pins but can leave a path along the jacket.

The fix is to bond and grip the jacket directly, over a long enough length to stop wicking, and to seal the connector body in the same moulding.

We would typically propose a silicone overmould with a primed jacket, moulded grip rings and a tapered strain relief, made through our partner network.

Illustrative example: Silicone overmould gripping cable jacket with moulded rings and tapered relief

What we would change

How we would move the seal to where the water gets in.

A modest design change, aimed squarely at the leak path.

  1. Jacket preparation

    The cable jacket cleaned and primed over the sealing length.

  2. Grip rings

    Moulded internal rings that compress onto the jacket to block water paths.

  3. Integrated strain relief

    A tapered boot that spreads bending load away from the joint.

  4. Low-temperature cure

    Grade and cure chosen to protect the connector and cable.

  5. Sacrificial trials

    Early samples cut open and pressure tested.

  6. Batch checks

    Continuity and sample pressure checks agreed for production batches.

Commercial trade-offs

How the trade-off would typically look.

An overmould tool is usually a modest investment compared with the hand work it replaces, because one moulding can take the place of the potting and heat-shrink steps.

Tooling and unit cost are quoted as separate lines, so you can weigh the tool against the assembly time it saves.

Services used

How we'd deliver a programme like this.

Cable and connector overmoulding

The point where a cable enters a connector or device is where most cables fail. An overmoulded silicone body seals that point, spreads the bending…

See the service

Hardware encapsulation

Wrapping a sensor, board or cable joint in silicone protects it from water, dust, vibration and hands. Done badly, it cracks solder joints or cooks…

See the service

Overmoulding

Silicone or rubber moulded directly onto a pre-made substrate — a plastic housing, a metal insert, a printed circuit assembly — so the finished part…

See the service
Illustrative example: Steel overmould tool with cable connector insert and finished sealed assemblies
Overmould tooling with sealed cable assemblies

More worked examples

Other programmes worth reading.

Illustrative example: Fabric-reinforced rubber diaphragms beside an open compression mould tool

Worked Example: Industrial Pump Diaphragm

A fabric-reinforced pump diaphragm where replacement parts fail early. This is how we would typically re-tool it in compression with the fabric layer…

Read the example
A TCI multi-cavity sheet mould on the production line

Worked Example: Wearable Overmoulded Button

Three separate parts bonded together by hand, failing at the bond line in drop testing. This is how we would typically approach moving the assembly to…

Read the example
Rubber gasket being measured with digital calipers

Worked Example: Medical Device LSR Gasket

A sealing gasket for a hand-held device housing. When a compression-moulded part needs hand-trimming on the sealing face, it stops scaling with volume…

Read the example

Next step

If your project rhymes with this one, get in touch.

The commercial shapes described in our worked examples are illustrative, not prices we're quoting today. Every programme sizes differently based on part geometry, annual volume, material family and paperwork requirements.

For a first conversation about whether we'd be the right supplier for your part, send a drawing or a sample with your rough annual volume. That's enough to know if the fit is real.

Designed and developed in the UK. Compression moulding and LSR on our own presses, with other work through our partner network. We'll confirm where your parts are made on your quotation.

At a glance

The idea in a picture.

How overmoulding works

Silicone moulded overPlastic, metal or electronicsBonded interface

Swipe to see the whole diagram

The rigid part goes into the tool and silicone is moulded around it, so you get one finished part.

Get in touch

Tell us the part, the volume, and the timeline.

Rough annual volume, target unit price, and any deadlines. That's enough to work out whether compression, LSR injection or something else is the right tool.

Real people, a real workshop

You deal with the people who make it.

No call centre and no middlemen. When you contact TCI Products, you speak to the team who design, build and check your mould.

  • A real Warwickshire workshopUnit 15, Waterloo Park, Bidford-on-Avon, Alcester B50 4JG.
  • Real people on the phoneCall the team on 01789 224228, Monday to Friday.
  • The same team on every jobDesign, production and aftercare come from the people you see here.
  • Part of TCI GroupFour specialist divisions under TCI Group, one engineering team. Visit TCI Group.
Representative image: moulds on the bench mid-build.
Representative image: moulds on the bench mid-build.
Representative image: a stack of silicone moulds.
Representative image: a stack of silicone moulds.
Representative image: a design and project office.
Representative image: a design and project office.
  • Thomas LaneManaging Director
  • George PrestonDesign & Project Manager
  • Kelly BallingerHead of Partnerships
  • Jim AndertonProduction Manager
  • TheodoreEmployee Welfare
Meet the team