Bidford-on-Avon, Warwickshire. Mon to Fri.01789 224228

Illustrative example · Sportswear · Overmoulding

Worked Example: Overmoulded Whistle

A referee whistle with a soft silicone mouthpiece bonded to a rigid plastic body, used in all weathers. This is how we would typically approach a mouthpiece that has to stay put for a full season.

SportswearSector
OvermouldTypical route
SeasonFull outdoor life
2019Established

The brief

A whistle whose mouthpiece has to stay on for a full season.

Illustrative example: Rigid whistle body with loosened silicone mouthpiece on a worn bench
Prototype whistle with mouthpiece fit problem

A typical brief: a whistle for referees with a rigid engineering-plastic body and a soft silicone mouthpiece for comfort in cold weather.

A press-fit mouthpiece can work at the bench but loosen in use, after being pressed against pockets and kit bags. A brief like this usually asks for the mouthpiece to be permanently bonded to the body rather than press-fit.

The problem

A press-fit depends on friction, and friction loosens.

Press-fit is cheap to assemble but relies on friction. Silicone stretches, friction fits loosen over time, and cold and wet conditions make it worse.

Overmoulding addresses that: silicone moulded directly onto the plastic body, chemically bonded during cure, with mechanical interlock features designed into the body. One part instead of two.

Typically the plastic body would come from your existing plastic moulder, primed before it reaches us, and the overmoulding would be made through our partner network.

Long TCI trough moulds on the bench

What we would change

How we would overmould the mouthpiece onto a primed plastic body.

A small design change on the plastic body, aimed at durability in use.

  1. Plastic body adapted for overmould

    Interlock features added around the mouthpiece area of the plastic body, tooled by the plastic supplier.

  2. Body primed before moulding

    The plastic supplier applies a light primer coat as their final step. Batch traceability is available on request.

  3. Silicone mouthpiece overmoulded

    Silicone moulded around the primed, interlocked body for a chemical bond plus mechanical retention.

  4. Brand colour matched

    Mouthpiece colour matched against a brand chip, with the recipe recorded.

  5. Pull test on first-off parts

    First-off parts pull-tested, looking for the silicone to tear before the bond separates.

  6. Packing to your specification

    Finished whistles can be packed to your specification for your fulfilment warehouse.

Illustrative example: Open overmould tool holding whistle body with interlock features
Whistle body prepared for silicone overmoulding

Commercial trade-offs

How the trade-off would typically look.

Overmoulding usually costs more per part than a press-fit assembly, plus the tooling. The case for it rests on removing the failure mode rather than on unit price.

Tooling and unit cost are quoted as separate lines, so you can weigh them against the cost of returns.

Services used

How we'd deliver a programme like this.

Overmoulding

Silicone or rubber moulded directly onto a pre-made substrate — a plastic housing, a metal insert, a printed circuit assembly — so the finished part…

See the service

Branded part manufacture

Silicone products moulded, finished, packaged and labelled to your brand — ready to ship into your retail, e-commerce or wholesale channel. Your…

See the service

Post-processing and finishing

Deflash, trim, print, bond, assemble, inspect and pack. Everything that has to happen between the press opening and the part being ready for your…

See the service

More worked examples

Other programmes worth reading.

Illustrative example: Compression press and trays of textured rubber grips in a workshop

Worked Example: Outdoor Rubber Grip

A textured rubber grip fitted to outdoor equipment. It needs to be UV-stable, weather-resistant and comfortable in cold and wet conditions. This is how…

Read the example
Illustrative example: Small silicone valves in a tray beside a multi-cavity tool.

Worked Example: Appliance Silicone Valve

A small silicone valve inside a domestic appliance. Never seen by the user, but it has to work every cycle for the life of the appliance. This is how…

Read the example
Illustrative example: Sealed cable connector overmould with a cut sample on a bench

Worked Example: Marine Connector Overmould

A connector on a sensor cable that sits in salt water. This is how we would typically approach replacing a potted joint and heat-shrink with a single…

Read the example

Next step

If your project rhymes with this one, get in touch.

The commercial shapes described in our worked examples are illustrative, not prices we're quoting today. Every programme sizes differently based on part geometry, annual volume, material family and paperwork requirements.

For a first conversation about whether we'd be the right supplier for your part, send a drawing or a sample with your rough annual volume. That's enough to know if the fit is real.

Designed and developed in the UK. Compression moulding and LSR on our own presses, with other work through our partner network. We'll confirm where your parts are made on your quotation.

At a glance

The idea in a picture.

How overmoulding works

Silicone moulded overPlastic, metal or electronicsBonded interface

Swipe to see the whole diagram

The rigid part goes into the tool and silicone is moulded around it, so you get one finished part.

Get in touch

Tell us the part, the volume, and the timeline.

Rough annual volume, target unit price, and any deadlines. That's enough to work out whether compression, LSR injection or something else is the right tool.

Real people, a real workshop

You deal with the people who make it.

No call centre and no middlemen. When you contact TCI Products, you speak to the team who design, build and check your mould.

  • A real Warwickshire workshopUnit 15, Waterloo Park, Bidford-on-Avon, Alcester B50 4JG.
  • Real people on the phoneCall the team on 01789 224228, Monday to Friday.
  • The same team on every jobDesign, production and aftercare come from the people you see here.
  • Part of TCI GroupFour specialist divisions under TCI Group, one engineering team. Visit TCI Group.
Representative image: a design and project office.
Representative image: a design and project office.
Representative image: moulds on the bench mid-build.
Representative image: moulds on the bench mid-build.
Representative image: a stack of silicone moulds.
Representative image: a stack of silicone moulds.
  • Thomas LaneManaging Director
  • George PrestonDesign & Project Manager
  • Kelly BallingerHead of Partnerships
  • Jim AndertonProduction Manager
  • TheodoreEmployee Welfare
Meet the team