Bidford-on-Avon, Warwickshire. Mon to Fri.01789 224228

Illustrative example · Industrial equipment · Compression

Worked Example: Industrial Pump Diaphragm

A fabric-reinforced pump diaphragm where replacement parts fail early. This is how we would typically re-tool it in compression with the fabric layer properly positioned.

IndustrialSector
CompressionTypical route
ReinforcedFabric layer

The brief

A diaphragm that has to flex for years.

Illustrative example: Fabric reinforced rubber diaphragms with failed split sample beside intact parts
Original and failed reinforced diaphragms compared

A typical brief: a maker of industrial dosing pumps relies on a fabric-reinforced rubber diaphragm. The original supply has stopped, and alternative parts are failing much earlier than the originals.

Samples of both are a good starting point: original parts that have run for years and replacement parts that have split. The ask is usually simple: diaphragms that last like the originals.

The problem

Where the fabric sits matters.

In a case like this, cutting open failed parts often shows the fabric layer off-centre, leaving a thin rubber section on one side that cracks under repeated flexing.

Well-performing parts keep the fabric central throughout the flexing zone.

The fix would be a compression tool and loading method that locates the fabric precisely and holds it there during cure.

Illustrative example: Detail: tray of moulded O-rings, gaskets and profile seals on a stainless inspection bench.

What we would change

How we would control the fabric position.

Most of the work is in the tool and the loading sequence.

  1. Section analysis

    Original and failed parts sectioned and compared.

  2. Compound match

    A compound chosen for the pumped media and flex life.

  3. Fabric location

    Tool features and pre-forms that hold the fabric centrally.

  4. Loading sequence

    A documented sequence for pre-forms and fabric.

  5. Section checks

    Sample parts sectioned to check fabric position.

  6. Life testing

    Samples supplied for your own pump life test.

Commercial trade-offs

What you would typically get from a programme like this.

The aim is diaphragms that match the originals in your own life testing, supplied in regular batches.

Tool ownership and storage are agreed on your quotation, and batch traceability is available on request.

Services used

How we'd deliver a programme like this.

Valves and diaphragms

A valve is judged on one thing: does it open and close the way it's supposed to, every time. That comes down to wall section, material hardness and…

See the service

Diaphragms

A diaphragm flexes many thousands of times, depending on design and compound. Its life depends on material, section and how evenly it was moulded.

See the service

Industrial compression moulding

Pads, buffers, bellows, grommets and seals for machines that have to keep running. Industrial compression work is about the right compound and a part…

See the service
Illustrative example: Compression press, steel tool and trays of diaphragms and valve parts
Compression moulding for diaphragms and valve parts

More worked examples

Other programmes worth reading.

A TCI multi-cavity sheet mould on the production line

Worked Example: Wearable Overmoulded Button

Three separate parts bonded together by hand, failing at the bond line in drop testing. This is how we would typically approach moving the assembly to…

Read the example
Rubber gasket being measured with digital calipers

Worked Example: Medical Device LSR Gasket

A sealing gasket for a hand-held device housing. When a compression-moulded part needs hand-trimming on the sealing face, it stops scaling with volume…

Read the example
A black TCI shaped-cavity silicone mould

Worked Example: Silicone Ear Tips

Small, soft, colour-critical parts that people wear for hours. This is how we would typically take a hand-cast pilot design into production tooling…

Read the example

Next step

If your project rhymes with this one, get in touch.

The commercial shapes described in our worked examples are illustrative, not prices we're quoting today. Every programme sizes differently based on part geometry, annual volume, material family and paperwork requirements.

For a first conversation about whether we'd be the right supplier for your part, send a drawing or a sample with your rough annual volume. That's enough to know if the fit is real.

Designed and developed in the UK. Compression moulding and LSR on our own presses, with other work through our partner network. We'll confirm where your parts are made on your quotation.

At a glance

The idea in a picture.

How overmoulding works

Silicone moulded overPlastic, metal or electronicsBonded interface

Swipe to see the whole diagram

The rigid part goes into the tool and silicone is moulded around it, so you get one finished part.

Get in touch

Tell us the part, the volume, and the timeline.

Rough annual volume, target unit price, and any deadlines. That's enough to work out whether compression, LSR injection or something else is the right tool.

Real people, a real workshop

You deal with the people who make it.

No call centre and no middlemen. When you contact TCI Products, you speak to the team who design, build and check your mould.

  • A real Warwickshire workshopUnit 15, Waterloo Park, Bidford-on-Avon, Alcester B50 4JG.
  • Real people on the phoneCall the team on 01789 224228, Monday to Friday.
  • The same team on every jobDesign, production and aftercare come from the people you see here.
  • Part of TCI GroupFour specialist divisions under TCI Group, one engineering team. Visit TCI Group.
Representative image: moulds on the bench mid-build.
Representative image: moulds on the bench mid-build.
Representative image: a stack of silicone moulds.
Representative image: a stack of silicone moulds.
Representative image: a design and project office.
Representative image: a design and project office.
  • Thomas LaneManaging Director
  • George PrestonDesign & Project Manager
  • Kelly BallingerHead of Partnerships
  • Jim AndertonProduction Manager
  • TheodoreEmployee Welfare
Meet the team