Bidford-on-Avon, Warwickshire. Mon to Fri.01789 224228

Illustrative example · Automotive tier-2 · Compression

Worked Example: Automotive Moulded Seal

A rubber sealing component supplied into a tier-1 that fits it into a vehicle. Not exotic and not complex, but it has to arrive when the build schedule needs it. This is how we would typically approach it.

Automotive tier-2Sector
EPDMMaterial family
CompressionTypical route
2019Established

The brief

A seal that has to arrive on time, in fluctuating volumes.

Illustrative example: Black EPDM seals in trays beside an open compression tool
Moulded seals prepared for responsive repeat supply

A typical brief: a tier-2 supplier sources an EPDM sealing component where the part itself is fine but the supply can't keep pace with a tier-1 build schedule that changes week to week.

To cover the gap, the tier-2 often carries extra safety stock, with the working capital, scrap risk and exposure that come with it. What they usually want is the same part and material spec, with supply that matches the build cadence.

The problem

The part is right. The supply model needs to fit the build rhythm.

A part like this usually needs no design change. It's a straightforward compression-moulded EPDM gasket to a spec the tier-2 already trusts. The challenge is the supply model, not the moulding.

We would typically propose a programme where the tool is made to the existing drawing, stock holding is agreed on the quotation, and batches are scheduled against a rolling forecast.

The commercial conversation is usually less about unit price and more about total cost of ownership, including inventory carrying cost and stock-out risk.

Bearings with moulded rubber seals

What we would change

How we would tool the part, agree stock holding and schedule batches.

The moulding is standard. The supply arrangement is where most of the work goes.

  1. Compression tool to the existing drawing

    Tool built to the existing drawing, with first parts measured against the drawing and compared with retained parts.

  2. Material spec verified

    EPDM compound checked against the original approval documentation and locked for the programme.

  3. Stock holding agreed

    Tool storage and stock holding can be arranged; we'll agree terms on your quotation.

  4. Batch supply against a schedule

    Batches scheduled against your build plan. We'll confirm lead times on your quotation.

  5. Regular forecast review

    A rolling forecast reviewed together, with batch timing adjusted to recent demand.

  6. Named engineer and escalation route

    A named engineer with a direct line, and an agreed route for urgent orders.

Illustrative example: Seal trays and buffer stock near compression press in workshop
Local stock held ready beside seal production

Commercial trade-offs

Where the value would typically sit.

On a programme like this, unit cost is rarely the main story. The value usually sits in matching supply to the build cadence and reducing the stock a buyer needs to carry.

We'll set out tooling, unit cost and any stock-holding terms on your quotation, so you can compare total cost rather than unit price alone.

Services used

How we'd deliver a programme like this.

Gasket and seal manufacture

Silicone and rubber gaskets moulded to your drawing, in the grade and hardness your sealing job actually needs. Enclosure gaskets, static fluid…

See the service

Compression moulding

Solid silicone or rubber pre-formed, loaded into a heated steel tool, and pressed under cure. Sensible tooling cost, built for repeat batches, and…

See the service

Batch manufacturing

For volumes measured in the hundreds or low thousands per batch, released on your schedule rather than ours. Bridge tooling, dedicated compression,…

See the service

More worked examples

Other programmes worth reading.

Illustrative example: Small silicone diaphragm held in gloved fingers above a parts tray

Worked Example: Haptics Silicone Diaphragm

A precision-shaped silicone diaphragm that generates haptic feedback in a small consumer device. This is how we would typically move a cast prototype…

Read the example
Illustrative example: Soft silicone applicator tips in a tray with one held up

Worked Example: Silicone Applicator Tip

A soft silicone tip for a personal care device. Skin contact, cleanable and colour-matched to the brand. This is how we would typically approach batch…

Read the example
Illustrative example: Overmoulded whistle parts with soft silicone mouthpieces on a bench

Worked Example: Overmoulded Whistle

A referee whistle with a soft silicone mouthpiece bonded to a rigid plastic body, used in all weathers. This is how we would typically approach a…

Read the example

Next step

If your project rhymes with this one, get in touch.

The commercial shapes described in our worked examples are illustrative, not prices we're quoting today. Every programme sizes differently based on part geometry, annual volume, material family and paperwork requirements.

For a first conversation about whether we'd be the right supplier for your part, send a drawing or a sample with your rough annual volume. That's enough to know if the fit is real.

Designed and developed in the UK. Compression moulding and LSR on our own presses, with other work through our partner network. We'll confirm where your parts are made on your quotation.

Get in touch

Tell us the part, the volume, and the timeline.

Rough annual volume, target unit price, and any deadlines. That's enough to work out whether compression, LSR injection or something else is the right tool.

Real people, a real workshop

You deal with the people who make it.

No call centre and no middlemen. When you contact TCI Products, you speak to the team who design, build and check your mould.

  • A real Warwickshire workshopUnit 15, Waterloo Park, Bidford-on-Avon, Alcester B50 4JG.
  • Real people on the phoneCall the team on 01789 224228, Monday to Friday.
  • The same team on every jobDesign, production and aftercare come from the people you see here.
  • Part of TCI GroupFour specialist divisions under TCI Group, one engineering team. Visit TCI Group.
Representative image: a design and project office.
Representative image: a design and project office.
Representative image: moulds on the bench mid-build.
Representative image: moulds on the bench mid-build.
Representative image: a stack of silicone moulds.
Representative image: a stack of silicone moulds.
  • Thomas LaneManaging Director
  • George PrestonDesign & Project Manager
  • Kelly BallingerHead of Partnerships
  • Jim AndertonProduction Manager
  • TheodoreEmployee Welfare
Meet the team