Bidford-on-Avon, Warwickshire. Mon to Fri.01789 224228

Illustrative example · Outdoor equipment · Compression

Worked Example: Outdoor Rubber Grip

A textured rubber grip fitted to outdoor equipment. It needs to be UV-stable, weather-resistant and comfortable in cold and wet conditions. This is how we would typically approach batch supply across a family of tools sharing one grip design.

Outdoor equipmentSector
EPDMMaterial family
CompressionTypical route
2019Established

The brief

A grip that has to cope with British weather across a product family.

Illustrative example: Textured rubber grip sleeves on handle cores in production bench scene
Textured rubber grips across a product family

A typical brief: a range of gardening and outdoor tools shares a common grip design, a textured rubber sleeve over the handle for comfort and control.

The grip has to feel comfortable in all conditions, survive UV exposure over a multi-year product life, and be recognisable as part of the family through consistent colour and texture.

The problem

The compound and the colour discipline both matter.

A general-purpose natural rubber compound is cheap and easy to mould, but it's the wrong choice outdoors. Natural rubber degrades in UV, with surface crazing, fading and a change in feel.

The right compound would typically be EPDM: UV-stable, weather-resistant and comfortable across the temperature range the tools will see. It's slightly more expensive per unit.

Colour discipline is the second part. A signature brand colour would be matched against a physical chip, so the whole range keeps looking like a family.

Illustrative example: Deep green EPDM grips compared with off-shade rubber samples on bench

What we would change

How we would set the compound, match colour against a physical chip and lock both.

Two disciplines, applied to a straightforward moulding job.

  1. Compound set to EPDM

    A weather-stable EPDM compound specified for outdoor use.

  2. Brand colour matched against a physical chip

    Colour matched against a physical chip signed off by your design team, with the pigment recipe recorded.

  3. Existing tools reviewed

    Where existing tools are transferred, they would be inspected and refurbished where needed. Tool ownership is agreed on your quotation.

  4. First parts across the range

    First parts from each tool measured against the drawing and compared to the golden sample for colour and texture.

  5. Batch supply against your forecast

    Batches scheduled against your forecast. Batch traceability is available on request.

  6. Extending the range

    New tools in the range can share the grip design, colour and texture.

Illustrative example: Deep green EPDM grips matched against physical colour chips on bench
EPDM grips checked for colour consistency

Commercial trade-offs

How the trade-off would typically look.

EPDM costs more per unit than natural rubber, so the choice is usually weighed against the warranty and reputation risk of grips that degrade outdoors.

Matching colour against physical chips adds little cost. It just needs doing once, properly, at the start of the programme.

Services used

How we'd deliver a programme like this.

Compression moulding

Solid silicone or rubber pre-formed, loaded into a heated steel tool, and pressed under cure. Sensible tooling cost, built for repeat batches, and…

See the service

Branded part manufacture

Silicone products moulded, finished, packaged and labelled to your brand — ready to ship into your retail, e-commerce or wholesale channel. Your…

See the service

Tooling and part continuity

For parts that will be in production for years — components inside a device family, sealing parts on long-lived equipment, consumer parts on a…

See the service

More worked examples

Other programmes worth reading.

Illustrative example: Small silicone valves in a tray beside a multi-cavity tool.

Worked Example: Appliance Silicone Valve

A small silicone valve inside a domestic appliance. Never seen by the user, but it has to work every cycle for the life of the appliance. This is how…

Read the example
Illustrative example: Sealed cable connector overmould with a cut sample on a bench

Worked Example: Marine Connector Overmould

A connector on a sensor cable that sits in salt water. This is how we would typically approach replacing a potted joint and heat-shrink with a single…

Read the example
Illustrative example: Fabric-reinforced rubber diaphragms beside an open compression mould tool

Worked Example: Industrial Pump Diaphragm

A fabric-reinforced pump diaphragm where replacement parts fail early. This is how we would typically re-tool it in compression with the fabric layer…

Read the example

Next step

If your project rhymes with this one, get in touch.

The commercial shapes described in our worked examples are illustrative, not prices we're quoting today. Every programme sizes differently based on part geometry, annual volume, material family and paperwork requirements.

For a first conversation about whether we'd be the right supplier for your part, send a drawing or a sample with your rough annual volume. That's enough to know if the fit is real.

Designed and developed in the UK. Compression moulding and LSR on our own presses, with other work through our partner network. We'll confirm where your parts are made on your quotation.

Get in touch

Tell us the part, the volume, and the timeline.

Rough annual volume, target unit price, and any deadlines. That's enough to work out whether compression, LSR injection or something else is the right tool.

Real people, a real workshop

You deal with the people who make it.

No call centre and no middlemen. When you contact TCI Products, you speak to the team who design, build and check your mould.

  • A real Warwickshire workshopUnit 15, Waterloo Park, Bidford-on-Avon, Alcester B50 4JG.
  • Real people on the phoneCall the team on 01789 224228, Monday to Friday.
  • The same team on every jobDesign, production and aftercare come from the people you see here.
  • Part of TCI GroupFour specialist divisions under TCI Group, one engineering team. Visit TCI Group.
Representative image: a stack of silicone moulds.
Representative image: a stack of silicone moulds.
Representative image: a design and project office.
Representative image: a design and project office.
Representative image: moulds on the bench mid-build.
Representative image: moulds on the bench mid-build.
  • Thomas LaneManaging Director
  • George PrestonDesign & Project Manager
  • Kelly BallingerHead of Partnerships
  • Jim AndertonProduction Manager
  • TheodoreEmployee Welfare
Meet the team