Bidford-on-Avon, Warwickshire. Mon to Fri.01789 224228

Illustrative example · UK wearables · Overmoulding

Worked Example: Wearable Overmoulded Button

Three separate parts bonded together by hand, failing at the bond line in drop testing. This is how we would typically approach moving the assembly to a single overmoulded part.

WearablesSector
OvermouldTypical route
3 to 1Assembly parts
2019Established

The brief

A button that has to survive being dropped, wet and worn.

Illustrative example: Failed three-part wearable button assembly separated into components
Original button assembly split into separate parts

A typical brief: a control button on a sports wearable has to survive drops onto hard surfaces, sweat and rain, and repeated pressing over the product's life. It also has to feel right, with a defined click, no wobble and no visible bond lines.

A common starting point is a three-part design, with a rigid plastic backing, a silicone dome and a printed cap adhesive-bonded on a fixture. If drop testing shows failures at the bond, the brief is usually to reduce the assembly steps and make the bond more reliable.

The problem

A hand-made bond is a labour operation, not a structural feature.

When the dome and backing come from different suppliers and are bonded during assembly, the bond depends on operator technique, adhesive age and cure conditions, all of which vary.

The fix isn't better glue. It's to form the bond under controlled moulding conditions: overmoulding.

We would typically propose a single overmoulded part: the plastic backing from your existing plastic supplier, with the silicone dome overmoulded onto it through our partner network, using a primed chemical bond plus mechanical interlock features.

Illustrative example: Overmoulded silicone button dome bonded onto small rigid plastic backing

What we would change

How we would simplify the assembly by moulding it as one part.

A small design change that can remove assembly steps.

  1. Backing adapted for overmould

    Mechanical interlock features added to the plastic backing, so the silicone stays locked in place.

  2. Backing primed before moulding

    Your plastic supplier applies a light primer before shipping. The primer bonds chemically to the silicone during cure.

  3. Dome overmoulded in one shot

    Silicone moulded around the primed, interlocked backing, with no adhesive step.

  4. Printing the finished part

    Graphics can be pad-printed on the moulded part through our partner network.

  5. First-off through your drop test

    First-off parts supplied for your own drop testing before production release.

  6. Delivered as one part

    Your assembly line would receive one part per button instead of three.

Illustrative example: Plastic button backings with ribs beside an overmould tool
Backings redesigned for one-piece button overmoulding

Commercial trade-offs

How the trade-off would typically look.

An overmould tool is an up-front cost. Against it, you weigh fewer parts in the bill of materials, fewer assembly steps and no bond-line rework loop.

Tooling and unit cost are quoted as separate lines. If volumes grow, the tool can be planned with a higher-cavity version in mind.

Services used

How we'd deliver a programme like this.

Overmoulding

Silicone or rubber moulded directly onto a pre-made substrate — a plastic housing, a metal insert, a printed circuit assembly — so the finished part…

See the service

Post-processing and finishing

Deflash, trim, print, bond, assemble, inspect and pack. Everything that has to happen between the press opening and the part being ready for your…

See the service

Branded part manufacture

Silicone products moulded, finished, packaged and labelled to your brand — ready to ship into your retail, e-commerce or wholesale channel. Your…

See the service

More worked examples

Other programmes worth reading.

Rubber gasket being measured with digital calipers

Worked Example: Medical Device LSR Gasket

A sealing gasket for a hand-held device housing. When a compression-moulded part needs hand-trimming on the sealing face, it stops scaling with volume…

Read the example
A black TCI shaped-cavity silicone mould

Worked Example: Silicone Ear Tips

Small, soft, colour-critical parts that people wear for hours. This is how we would typically take a hand-cast pilot design into production tooling…

Read the example
Illustrative example: Silicone keypad mats and inspection tools on a workshop bench

Worked Example: Electronics Keypad Batch

A silicone keypad mat for a hand-held industrial device. Buttons that feel decisive without being noisy, conductive contacts that close reliably, and…

Read the example

Next step

If your project rhymes with this one, get in touch.

The commercial shapes described in our worked examples are illustrative, not prices we're quoting today. Every programme sizes differently based on part geometry, annual volume, material family and paperwork requirements.

For a first conversation about whether we'd be the right supplier for your part, send a drawing or a sample with your rough annual volume. That's enough to know if the fit is real.

Designed and developed in the UK. Compression moulding and LSR on our own presses, with other work through our partner network. We'll confirm where your parts are made on your quotation.

At a glance

The idea in a picture.

How overmoulding works

Silicone moulded overPlastic, metal or electronicsBonded interface

Swipe to see the whole diagram

The rigid part goes into the tool and silicone is moulded around it, so you get one finished part.

Get in touch

Tell us the part, the volume, and the timeline.

Rough annual volume, target unit price, and any deadlines. That's enough to work out whether compression, LSR injection or something else is the right tool.

Real people, a real workshop

You deal with the people who make it.

No call centre and no middlemen. When you contact TCI Products, you speak to the team who design, build and check your mould.

  • A real Warwickshire workshopUnit 15, Waterloo Park, Bidford-on-Avon, Alcester B50 4JG.
  • Real people on the phoneCall the team on 01789 224228, Monday to Friday.
  • The same team on every jobDesign, production and aftercare come from the people you see here.
  • Part of TCI GroupFour specialist divisions under TCI Group, one engineering team. Visit TCI Group.
Representative image: a design and project office.
Representative image: a design and project office.
Representative image: moulds on the bench mid-build.
Representative image: moulds on the bench mid-build.
Representative image: a stack of silicone moulds.
Representative image: a stack of silicone moulds.
  • Thomas LaneManaging Director
  • George PrestonDesign & Project Manager
  • Kelly BallingerHead of Partnerships
  • Jim AndertonProduction Manager
  • TheodoreEmployee Welfare
Meet the team