Bidford-on-Avon, Warwickshire. Mon to Fri.01789 224228

Illustrative example · Haptics · LSR

Worked Example: Haptics Silicone Diaphragm

A precision-shaped silicone diaphragm that generates haptic feedback in a small consumer device. This is how we would typically move a cast prototype to production LSR and keep it consistent.

HapticsSector
LSRTypical route
Multi-cavityProduction tool
2019Established

The brief

A diaphragm whose deflection has to be repeatable to the touch.

Illustrative example: Small silicone diaphragm being lightly flexed beside precision insert
Diaphragm deflection checked for consistent tactile response

A typical brief: a small silicone diaphragm produces tactile feedback in a hand-held device. Prototype casting has validated the concept and user testing has confirmed the haptic profile.

For production, the challenge is consistency. If stiffness varies from part to part, the feedback varies, and users notice. What's needed is a production route that holds diaphragm stiffness within a tight window across every batch.

The problem

Diaphragm stiffness depends on wall thickness, grade and cure, so all three need locking.

Cast prototypes are made one at a time, so every part is slightly different. That's fine at prototype stage, where the overall character is what's being tested.

In production, every user experiences their own device, so individual variation matters. Small changes in wall thickness translate directly into perceived stiffness.

The route would typically be LSR with tight cavity control, a grade with well-characterised cure behaviour, and a cure cycle held to specification. The three interlock, so getting one wrong shows in the finished part.

Close-up of a dense circuit board

What we would change

How we would tool LSR to a tight cavity spec, check stiffness on real parts and lock the cure.

If the design is right, the route change does most of the work.

  1. Cavity finish for dimensional control

    The cavity machined and polished to hold wall thickness to a defined tolerance, with wear tracked over the tool's life.

  2. Grade chosen on cure behaviour

    An LSR grade chosen for repeatable cure behaviour across batches.

  3. Stiffness testing on sample parts

    First production samples deflection-tested, with grade and cure adjusted where needed to tighten the spread.

  4. Cure cycle locked

    Cure time, temperature and pressure documented, with any deviation needing quality sign-off.

  5. Golden sample and stiffness reference

    A golden sample and a stiffness reference set from the first production batch and retained.

  6. Batches to spec

    First-off parts from each batch checked for dimensions and haptic performance.

Illustrative example: Polished LSR tool and diaphragm stiffness test bench with sample parts
LSR diaphragm tooling and stiffness check

Commercial trade-offs

How the tooling cost would typically be weighed.

Multi-cavity LSR tooling is a larger up-front cost than casting, so it's usually weighed against the volume forecast.

Per-part cost in LSR production is typically lower than cast prototype production. Tooling and unit cost are quoted as separate lines, so you can see the trade-off.

Services used

How we'd deliver a programme like this.

LSR injection moulding

Two-part liquid silicone metered, mixed, injected cold and cured hot. The cleanest route we have for medical, wearable and electronics parts at…

See the service

Wearable and consumer silicone

Silicone parts for products people wear, hold, or wipe every day — ear tips, straps, grips, sleeves, applicators. Made to a colour and feel you sign…

See the service

Tooling and part continuity

For parts that will be in production for years — components inside a device family, sealing parts on long-lived equipment, consumer parts on a…

See the service

More worked examples

Other programmes worth reading.

Illustrative example: Soft silicone applicator tips in a tray with one held up

Worked Example: Silicone Applicator Tip

A soft silicone tip for a personal care device. Skin contact, cleanable and colour-matched to the brand. This is how we would typically approach batch…

Read the example
Illustrative example: Overmoulded whistle parts with soft silicone mouthpieces on a bench

Worked Example: Overmoulded Whistle

A referee whistle with a soft silicone mouthpiece bonded to a rigid plastic body, used in all weathers. This is how we would typically approach a…

Read the example
Illustrative example: Compression press and trays of textured rubber grips in a workshop

Worked Example: Outdoor Rubber Grip

A textured rubber grip fitted to outdoor equipment. It needs to be UV-stable, weather-resistant and comfortable in cold and wet conditions. This is how…

Read the example

Next step

If your project rhymes with this one, get in touch.

The commercial shapes described in our worked examples are illustrative, not prices we're quoting today. Every programme sizes differently based on part geometry, annual volume, material family and paperwork requirements.

For a first conversation about whether we'd be the right supplier for your part, send a drawing or a sample with your rough annual volume. That's enough to know if the fit is real.

Designed and developed in the UK. Compression moulding and LSR on our own presses, with other work through our partner network. We'll confirm where your parts are made on your quotation.

Get in touch

Tell us the part, the volume, and the timeline.

Rough annual volume, target unit price, and any deadlines. That's enough to work out whether compression, LSR injection or something else is the right tool.

Real people, a real workshop

You deal with the people who make it.

No call centre and no middlemen. When you contact TCI Products, you speak to the team who design, build and check your mould.

  • A real Warwickshire workshopUnit 15, Waterloo Park, Bidford-on-Avon, Alcester B50 4JG.
  • Real people on the phoneCall the team on 01789 224228, Monday to Friday.
  • The same team on every jobDesign, production and aftercare come from the people you see here.
  • Part of TCI GroupFour specialist divisions under TCI Group, one engineering team. Visit TCI Group.
Representative image: moulds on the bench mid-build.
Representative image: moulds on the bench mid-build.
Representative image: a stack of silicone moulds.
Representative image: a stack of silicone moulds.
Representative image: a design and project office.
Representative image: a design and project office.
  • Thomas LaneManaging Director
  • George PrestonDesign & Project Manager
  • Kelly BallingerHead of Partnerships
  • Jim AndertonProduction Manager
  • TheodoreEmployee Welfare
Meet the team