Bidford-on-Avon, Warwickshire. Mon to Fri.01789 224228

Illustrative example · Consumer audio · LSR

Worked Example: Silicone Ear Tips

Small, soft, colour-critical parts that people wear for hours. This is how we would typically take a hand-cast pilot design into production tooling while holding the feel and colour.

Consumer audioSector
LSRTypical route
Multi-cavityTool type
2019Established

The brief

Ear tips that have to feel the same, batch after batch, across sizes and colours.

Illustrative example: Silicone ear tips in multiple sizes and colours on trays
Ear tip sizes and colours prepared for comparison

A typical brief: a consumer audio product has been validated with hand-cast silicone ear tips, and the design has been signed off on feel and fit.

For production, the same tip geometry is needed in several sizes and colourways, and the feel has to match the pilot samples the design was signed off against. A brief like this usually covers cavity count, colour matching, batch consistency and packing.

The problem

Hand-cast pilot samples and moulded production parts don't feel identical.

Hand-cast samples don't feel identical to LSR-moulded production parts, even in the same grade. Cure conditions, surface finish and internal stress all differ. Moving to production without addressing that can produce ear tips that meet the drawing but don't feel like what was signed off.

We would typically propose LSR sample parts in the intended production grade and cavity finish, compared directly with the pilot samples. Any difference would drive an adjustment to grade or finish before the production tool is cut.

Colour is the other challenge. Subtle shades photograph differently under different lighting, so matching would be done against physical chips under standard lighting, then held across every batch.

Technician in cleanroom clothing at a machine

What we would change

How we would prototype in LSR, match colour against chips, then tool for volume.

The pattern: prove the production route matches the signed-off feel, lock colour, then commit to tooling.

  1. LSR sample parts in production grade

    Sample parts in the intended grade and finish, compared directly with the hand-cast pilot samples.

  2. Colour matching against physical chips

    Colours matched against physical silicone chips rather than reference numbers, signed off by your product team, with pigment recipes recorded.

  3. Multi-size production tool

    Where it suits the product family, several cavity sizes can share one tool base.

  4. Cold-runner LSR for clean release

    A cold-runner tool design keeps witness marks off the visible ear tip surface.

  5. First parts against the pilot reference

    First production parts measured against the drawing and compared with the retained pilot samples for feel and colour.

  6. Packing to your specification

    Ear tips can be packed to your specification, ready for your distribution warehouse.

Illustrative example: Open ear tip tool with fresh parts and colour chips
LSR samples and colour matching before volume tooling

Commercial trade-offs

How the tooling cost would typically be weighed.

Multi-cavity LSR tooling is a significant investment, so it's usually scoped against a multi-year volume forecast.

Per-part cost in production is typically lower than hand-cast pilot production. Tooling and unit cost are quoted as separate lines, so you can see the trade-off before you commit.

Services used

How we'd deliver a programme like this.

LSR injection moulding

Two-part liquid silicone metered, mixed, injected cold and cured hot. The cleanest route we have for medical, wearable and electronics parts at…

See the service

Wearable and consumer silicone

Silicone parts for products people wear, hold, or wipe every day — ear tips, straps, grips, sleeves, applicators. Made to a colour and feel you sign…

See the service

Branded part manufacture

Silicone products moulded, finished, packaged and labelled to your brand — ready to ship into your retail, e-commerce or wholesale channel. Your…

See the service

More worked examples

Other programmes worth reading.

Illustrative example: Silicone keypad mats and inspection tools on a workshop bench

Worked Example: Electronics Keypad Batch

A silicone keypad mat for a hand-held industrial device. Buttons that feel decisive without being noisy, conductive contacts that close reliably, and…

Read the example
Illustrative example: Black rubber seals in trays beside a compression mould tool

Worked Example: Automotive Moulded Seal

A rubber sealing component supplied into a tier-1 that fits it into a vehicle. Not exotic and not complex, but it has to arrive when the build schedule…

Read the example
Illustrative example: Small silicone diaphragm held in gloved fingers above a parts tray

Worked Example: Haptics Silicone Diaphragm

A precision-shaped silicone diaphragm that generates haptic feedback in a small consumer device. This is how we would typically move a cast prototype…

Read the example

Next step

If your project rhymes with this one, get in touch.

The commercial shapes described in our worked examples are illustrative, not prices we're quoting today. Every programme sizes differently based on part geometry, annual volume, material family and paperwork requirements.

For a first conversation about whether we'd be the right supplier for your part, send a drawing or a sample with your rough annual volume. That's enough to know if the fit is real.

Designed and developed in the UK. Compression moulding and LSR on our own presses, with other work through our partner network. We'll confirm where your parts are made on your quotation.

Get in touch

Tell us the part, the volume, and the timeline.

Rough annual volume, target unit price, and any deadlines. That's enough to work out whether compression, LSR injection or something else is the right tool.

Real people, a real workshop

You deal with the people who make it.

No call centre and no middlemen. When you contact TCI Products, you speak to the team who design, build and check your mould.

  • A real Warwickshire workshopUnit 15, Waterloo Park, Bidford-on-Avon, Alcester B50 4JG.
  • Real people on the phoneCall the team on 01789 224228, Monday to Friday.
  • The same team on every jobDesign, production and aftercare come from the people you see here.
  • Part of TCI GroupFour specialist divisions under TCI Group, one engineering team. Visit TCI Group.
Representative image: moulds on the bench mid-build.
Representative image: moulds on the bench mid-build.
Representative image: a stack of silicone moulds.
Representative image: a stack of silicone moulds.
Representative image: a design and project office.
Representative image: a design and project office.
  • Thomas LaneManaging Director
  • George PrestonDesign & Project Manager
  • Kelly BallingerHead of Partnerships
  • Jim AndertonProduction Manager
  • TheodoreEmployee Welfare
Meet the team